BinanceSmartChain RPC endpoint
From Chainlink Community Wiki
This is a general guide on deploying an Binance Smart Chain RPC endpoint for your Chainlink Node(s).
Official Binance Smart Chain Docs are available here
Note: This document assumes base operating system is Debian 10
Binance Smart Chain RPC Endpoints:
- Websocket
ws://<your_ip_address>:8546
- HTTP
http://<your_ip_address>:8545
Install Dependencies
Before we can get our Binance Smart Chain node running, we need to install some necessary software.
we'll install some packages that we'll need or will at least be handy to have.
sudo apt install -y git curl wget jq node-ws telnet traceroute
Install Go
Navigate to the official Go download page at go.dev/doc/install, and copy the link address for the download button.
Once you have the link, we'll use wget to download it.
Please remember that the below examples have <version> in lieu of the release that was applicable at the time of writing
wget https://go.dev/dl/go<version>.linux-amd64.tar.gz
This will download the tarball, which we will see is named go<version>.linux-amd64.tar.gz.
To start, we'll want to extract the tarball
tar xvf go<version>.linux-amd64.tar.gz
Now that the packages has been extracted, we should have a new directory named, go
We'll adjust permissions on the directory, then relocate it to out /usr/local/ directory.
sudo chown -R root:root ./go
sudo mv go /usr/local/
And then, we'll modify our ~/.profile file and then force a reload of it.
nano ~/.profile
We'll want to add the following to the bottom of the ~/.profile file
export GOPATH=$HOME/go
export PATH=$PATH:/usr/local/go/bin:$GOPATH/bin
Copy
Once those lines have been added to our profile, we need to force our TTY session to load it.
source ~/.profile
We'll know all is well when we check to see the path to the command and check to see what version of Go we have installed
which go
You should get /usr/local/go/bin/go as the path to the command
go version
We should see the newly installed verison, go version go<version> linux/amd64
Download & Install Binance Smart Chain Node Software
First we'll need to clone the bnb-chain repository
git clone https://github.com/bnb-chain/bsc.git
Once cloned, we'll change directories into the newly downloaded bnb-chain directory
cd bnb-chain
Then, we'll compile the necessary binaries, just like we would with geth
make all
Once it's finished compiling the binaries, we will be able to find them in the build directory, ~/bnb-chain/build/bin/geth.
we can check to confirm the operation of the binary by checking the verison
./build/bin/geth --version
Create Binance Smart Chain Node Service
Create a new service file for your binance smart chain node.
sudo nano /etc/systemd/system/binance-node.service
Copy and paste the below into the new file, modifying the necessary values
We'll want to update the <username> to your correct value.
[Unit]
Description=Binance Smart Chain RPC Node
After=network.target auditd.service
Wants=network.target
[Service]
Type=simple
User=<username>
WorkingDirectory=/home/<username>/.binancesmartchain/
TimeoutStartSec=0
TimeoutStopSec=120
ExecStart=/home/<username>/bnb-chain/build/bin/geth \
--mainnet \
--cache 8192 \
--log.json \
--verbosity 2 \
--metrics \
--http \
--http.addr 0.0.0.0 \
--http.vhosts '*' \
--ws \
--ws.addr 0.0.0.0 \
--ws.origins 0.0.0.0 \
--datadir /home/<username>/.binancesmartchain/
Restart=always
RestartSec=10s
[Install]
WantedBy=multi-user.target
RequiredBy=swarm.service
Alias=binance-node.service
Start Binance Smart Chain Node Service
Once we have the service file created, we can start it with a simple command, but first, we'll reload our daemons to be sure that it detects the newly created service file.
sudo systemctl daemon-reload
Then,
sudo systemctl start binance-node.service
Check Status of Binance Smart Chain Node Service
We can check the status of the service itself by checking the system logs for the specific service
sudo journalctl -u binance-node.service
If we want to check the status/state of the endpoints sync, we can simply query the RPC endpoint to see what the block height is, and compare that against the explorer.
Here's a simple bash script that does exactly that.
be sure to add your api key in place of <api_key>
#!/bin/bash
# blue foreground
blue_fg=$(tput setaf 6)
# reset to default
reset=$(tput sgr0)
# SET VARS
BLOCK_HEIGHT=$(curl -s -H "Content-Type: application/json" http://localhost:8545 -d '{"jsonrpc": "2.0", "id": 123, "method": "eth_blockNumber"}' | jq -r .result)
BSCSCAN_BLOCK_HEIGHT=$(curl -s -d "action=eth_blockNumber&apikey=<api_key>&module=proxy" -X POST https://api.bscscan.com/api | jq -r .result)
PEER_COUNT=$(curl -s -H "Content-Type: application/json" http://localhost:8545 -d '{"jsonrpc":"2.0","method":"net_peerCount","params":[],"id":74}' | jq -r .result)
IS_SYNCING=$(curl -s -H "Content-Type: application/json" http://localhost:8545 -d '{"jsonrpc": "2.0", "id": 123, "method": "eth_syncing"}' | jq .)
echo "----------------------"
echo "RPC Node block height: ${blue_fg}$((BLOCK_HEIGHT))${reset}"
echo "BSCScan block height: ${blue_fg}$((BSCSCAN_BLOCK_HEIGHT))${reset}"
echo "Current peer count: ${blue_fg}$((PEER_COUNT))${reset}"
VAR1=$(curl -s -H "Content-Type: application/json" http://localhost:8545 -d '{"jsonrpc": "2.0", "id": 123, "method": "eth_syncing"}' | jq .result)
VAR2="false"
if [ "$VAR1" = "$VAR2" ]; then
echo "Sync Status: ${blue_fg}Node is synced.${reset}"
else
echo "${blue_fg}Node is ${yellow_fg}NOT${blue_fg} synced.${reset}"
fi